Aplicações

Determination of Cr, Mn, and Ti in a PTA solution containing HCl.

Determination of styrene monomers in polystyrene. Free styrene is converted to a polarographically active pseudonitrosite.

To monitor the quality of PVC (polyvinyl chloride), it is important to measure the molecular weight during the production process, as this parameter has a significant influence on chemical and mechanical stability as well as fire retardant properties. The standard method to determine PVC molecular weight, defined here as the average weight of the molecules that make up the polymer, is by size exclusion chromatography (SEC). This analytical method is time-intensive and requires trained personnel to perform. Determining the molecular weight of PVC is easier with near-infrared spectroscopy (NIRS). NIRS provides results in just a few seconds and can quickly indicate when adjustments to the production process are necessary.are necessary.

PVC (polyvinyl chloride) foils with a PVDC (polyvinylidene chloride) coating are often used for high performance packaging films like pharmaceutical blister packs or in food packaging. In multi-layer blister films, the PVC serves as the thermoformable backbone structure, whereas the PVDC coating acts as a barrier against moisture and oxygen. The Water Vapor Transmission Rate (WVTR) and Oxygen Transmission Rate (OTR) are influenced by the composition and the thickness of the coating. A fast way to monitor PVDC coating thickness is with near-infrared spectroscopy. Results are provided in a few seconds, indicating when adjustments in the polymer production process are necessary.

Near-infrared (NIR) spectroscopy is able to determine the intrinsic viscosity of rPET in less than one minute without any sample preparation. This Application Note demonstrates that the Metrohm DS2500 Solid Analyzer operating in the visible and near-infrared spectral region (Vis-NIR) offers users an easier way to perform this analysis without the use of toxic chemicals.

Aromatic dicarboxylic acids, e.g., terephthalate, isophthalate and 5-sulfoisophthalate, are important monomers in the manufacture of polyesters and alkyd resins. The monomer ratio of the dicarboxylic acids has an enormous influence on polymerization. The separation of the late-eluting components is completed within 15 minutes if a short Metrosep A Supp 15 - 50/4.0 type column is used together with high eluent concentrations and flow rates.

Carbonyl compounds occur in many products such as bio-oils and fuels, solvents, flavors, and mineral oils. Carbonyl compounds are often prone to oxidation and thus their content has an influence on stability during storage or processing. Especially for pyrolysis bio-oils, stability issues are observed during storage, handling, and upgrading. Oils are dissolved in isopropanol. After a reaction with the hydroxylamine hydrochloride at 50 °C, a fast and accurate determination by potentiometric titration using the dSolvotrode and tetra-n-butylammonium hydroxide as titrant is performed.

The presence of excessive water in plastics adversely affects the performance of polymeric goods which is why water determination is of crucial importance. This article describes the accurate and straightforward determination of the water content using the Karl Fischer Oven Method in ten different plastic types that are not amenable to direct Karl Fischer titration. The experiments revealed that besides the determination of the oven temperature, sample preparation is one of the most important steps of the analysis, especially in case of hygroscopic plastic samples.

Carbonyl compounds (CC) occur in many products, such as bio-oils and fuels, cyclic and acyclic solvents, flavors and mineral oils. Carbonyl compounds can be responsible for the instability of these products during storage or processing. Especially pyrolysis bio-oils are known to cause issues during storage, handling and upgrading. This bulletin describes an aqueous and a non-aqueous analytical titration method for the determination of carbonyl compounds by potentiometric titration.

Polystyrol is brominated to increase flame retardation. The brominated polystyrene finally consists of 25 to 35% of bromine. The determination of bromine by combustion ion chromatography (CIC) requires a specially optimized absorption solution to trap all bromide. This work shows the optimization of the absorption solution for high-bromine samples.